Description: KAKUTE F4 FLIGHT CONTROLLER V2Specification:MCU: STM32F405RGT6 32-bit processorIMU: ICM20689 (SPI)Barometer: BMP280USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)5 hardware UARTS (UART1,3,4, 5, 6)Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.128 Mbit Dataflash chip for Blackbox loggingDimensions: 35x30x8mm (includes USB in height)Mounting Holes: Standard 30.5mm square to center of holesWeight: 7gFeaturesSupports Betaflight and Cleanflight.Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz.2 oz. copper PCB allows up to 120A maximum continuous current.Dedicated bootloader button for easy firmware flashing.Low-profile design fits into even very compact frames.Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 AIO monitors voltage directly from the battery power lead.Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.Supports BLHeli pass-through for easy ESC upgrade and configuration.New V2 FeaturesAdditional UART (UART 4) added to support serial camera communication such as to RunCam Split. Please note this is NOT the same as Betaflight Camera Control feature, which controls the menu of FPV cameras like Swift, Monster, etc.Additional UART (UART 5) added to support ESC telemetry such as from BLHeli_32 and KISS.Through-hole solder pads instead of flat pads for more secure soldering especially for beginners.Barometer sensor on board allows altitude hold mode.I2C pad available for certain external sensors.Tekko32 4-in-1 35A ESCSpecification:Supports 3-6S lipo input35A continuous current, 50A burstMounting holes 30.5x30.5mmSize: 55*40*6.4mmWeight: 17gFeature:4in1 ESC with 30.5x30.5mm mounting holes, supports DSHOT 1200, BLHELI32 firmware.On this version added more CAPS to reduce power noise.32bit ESC with BLHELI32 firmware4PWM inputVoltage output (VBAT), ESC Telemetry(TELEM)Supports Oneshot / Multishot / Dshot PWMSupports damped lightNO BECAtlatl HVSpecification:MCU: STM32F405RGT6 32-bit processorIMU: ICM20689 (SPI)USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)3 hardware UARTS (UART1,3,6)128 Mbit Dataflash chip for Blackbox loggingDimensions: 35x43x7mm (includes USB in height)Mounting Holes: Standard 30.5mm square to center of holesWeight: 7gFeature:Supports Betaflight and Cleanflight.Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz.2 oz. copper PCB allows up to 120A maximum continuous current.Dedicated bootloader button for easy firmware flashing.Low-profile design fits into even very compact frames.Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “BAT” pad only).Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 AIO monitors voltage directly from the battery power lead.Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.Supports BLHeli pass-through for easy ESC upgrade and configuration.
Price: 109 USD
Location: Catharpin, Virginia
End Time: 2024-02-12T00:38:21.000Z
Shipping Cost: N/A USD
Product Images
Item Specifics
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Brand: Holybro
Type: Electronic (ESC)
Model: 20033
MPN: 20033
